上海煥堯機電設備有限公司 

威廉工業控制

您身邊的歐洲工業自動化代購專家

品牌負責：程工（William）
Adress：中國上海市嘉定區嘉定新城
 

詢價請認真對待，公司設有統一的黑名單制度

愿每一份報價都被溫柔以待！?。?/span>

原廠 傳感器 編碼器 流量計 閥泵 夾具 電機 檢測器 風扇 減速機 控制模塊、隔離放大器、變送器、逆變器、變頻器、總線模塊、電容、流量開關、接近開關、光柵尺、讀數頭、絕緣檢測儀、遠程報警器、分析儀、數據采集器、溫控儀、傳動軸、軸承、軸套、接頭、剎車片、伺服閥、泵、濾芯、密封圈、過濾器

您只需提供品牌+型號（附帶銘牌）
優勢電氣類：P+F、Balluff、Turck、Phoenix、SUCO、MURR、Burster、B&R、Jumo、Schunk 、CON-TRINEX、Voltcraft等 
優勢液壓類：Rexroth、Hydac、蒙特貝Z92、Parker等各類德國進口工控備件

美國Hitec Products，Inc(HPI）在應力計行業擁有超過50年的經驗，HPI是惡劣環境傳感器和應力計配件的主要供應商。
美國HPI的應變計廣泛用于高溫和防水環境下的動態和靜態應變測量。

能測試溫度達到850°C的高溫應變片

SPECIFICATIONS:

Gage Grid: .......................Fe Cr Al Alloy (.001") .003mm diameter round wire
Leads: ..............................Fe Cr Al Alloy (.003") .008mm diameter round wire
with “Z” configuration flattened to (.0015") .004 mm
in grid area
Carrier: ............................Fiberglass reinforced Teflon tape carrier with silicone
adhesive (shelf life of grid carrier [Figure 2] is 9 months)
Resistance: ......................120.0 ohms ± 2.0 ohms at 20°C (68°F)
Gage Factor: ...................2.4 nominal at 20°C (68°F)
Gage Current: .................30 Milliamperes, max.
Temperature Range: ......Cryogenic to 850°C (1560°F)
Weldable Gage ONLY:
Shim Material: ................Hasloy X
Bonding Matrix: .............Alumina
Shelf Life: ........................Unlimit

Density: ............................................................. 7.1 Mg/m3 (0.256 lb./in3)

Chemical Analysis, Approx.: ....................... 72 Fe 22.5 Cr 5.5 Al
Resistivity @ 20°C (68°F): ............................ 875, ohms - cmf
Max. Operating Temperature: ................... 1375°C (2500°F)
Melting Point, Approx.: ................................ 1510°C (2750°F)
Temperature Factor,
Resistant Max. Temp.: ................................... 1.044
Thermal Expansion, ppm/°F: ..................... 20 - 250°C = 6.1 (68 - 482°F)
20 - 500°C = 6.9 (68 - 932°F)
20 - 750°C = 7.7 (68 - 1382°F)
20 - 1000°C = 8.3 (68 - 1832°F)
Gage Factor K @ 20°C (68°F): .................... 2.3 to 2.6
Gage Factor vs. Temperature
Coefficient:................................ -5.73 x 10-4/°C
Tensile Strength, PSI: .................................... 140,000 (hard), 92,000 (soft)
Tensile Strength, MPa: .................................. 965 (hard), 690 (soft)
Elongation, % (Soft): ..................................... 22%
Magnetic: ......................................................... Yes, below 540°C (1000°F)
Thermoelectric Potential vs. Cu: ............... -2.6μV/°C (0-100°C)