玻璃鱗片膠泥作為防腐層zui簡單的方法，就是使流體介質與基體隔絕，而膠泥涂料通常存在孔隙，流體介質（水、酸、堿等）小分子的直徑一般比涂層的孔隙要小，加上這些與涂層接觸的介質都是直線地通過，而涂層又不可能涂得很厚（否則要產生裂紋），一般的膠泥涂料即使可以較好地耐其所接觸的介質腐蝕，但它抵擋不住介質向基體的擴散滲透。所以，普通的防腐涂料一般只能作為大氣防腐而不能起到襯里的作用，尤其在液相介質和溫度較高的場合。玻璃鱗片膠泥的加入使涂料發生了二方面的變化，一是可以加工成很厚而不要擔心會發生裂紋，這是因?yàn)椴Ａ[片把涂層分割成許多小的空間而大大地降低了涂層的收縮應力和膨脹系數；二是由于玻璃鱗片膠泥的多層平行與基體排列，使介質擴散滲透的路線變得彎彎曲曲，增大了介質滲透擴散至基體的阻力。用于涂料中的玻璃鱗片膠泥具有魚鱗效應：成千上萬的鱗片交錯排列，形成涂層內復雜曲折的滲透擴散途徑，使得腐蝕介質的擴散路線變得相當曲折，很難達到基材。
【玻璃鱗片膠泥介紹】
名稱：玻璃鱗片膠泥
組成：玻璃鱗片、固化劑、耐磨填料、乙烯基樹脂等
特點：
乙烯基玻璃鱗片膠泥擁有優良的耐化學介質、高溫濕態腐蝕性氣體性能。
極低的水蒸氣滲透了、硬化收縮率、線膨脹系數低。
充分抵擋高溫及溫度驟變，較低的磨耗性能。
常溫硬化，成型施工簡單，修補容易。
適用范圍：
石油貯槽、化學品油船、鐵路橋梁等的表面涂覆。
海洋工程工程建筑物、鋼結構的防腐。
管道煙氣脫硫（FGD）裝置的耐蝕襯里，其zui高使用溫度可達180℃。
建筑物地面、排水溝、污水池的耐蝕覆蓋層。
使用方法：
鋼結構便面除油去污，除銹等級不低于Sa2.0或St3標準；混凝土表面清理干凈，表面含水率 <6%，底漆涂刷1至2道，待干后施工。
用手工刮刀刮鏝成1-2mm（每道）的膠泥層，數小時硬化后再設計要求施工至規定厚度。
在彎角或者形狀突變處適當增加厚度，或用FPR增強，zui后用漆罩面1至2道。
包裝和保存：
本品用25kg鐵通包裝，在陰涼干燥處密封保存，25℃下有效保存期為三個月。
Method of glass flake coating as the most simple, is to make the fluid medium and matrix isolation, and clay paint are pore fluid medium (water, acid, alkali and other small molecules) are generally higher than the coating pore diameter is smaller, and the contact with the coating medium are straight through, and coating it can not be painted very thick (or cracks), clay coatings generally even better corrosive medium of the contact, but it could not withstand the permeability to the matrix diffusion. Therefore, generally only the ordinary anticorrosive coating for atmospheric corrosion can not play the role of the liner, especially in liquid medium and high temperature applications. Adding glass flake clay to paint has changed in two aspects, one is can be processed into very thick and don't worry about the occurrence of crack, this is because the glass flake coating is divided into many small Space and greatly reduce the coating of shrinkage stress and expansion coefficient; the second is due to the fact that the glass flake clay layers of parallel and matrix arrangement, and the medium penetration and diffusion of route to become crooked, increasing the medium permeability resistance of diffusion to the substrate. For coating glass scale clay has scale effect: scales of tens of thousands of staggered to form coating in complex and tortuous diffusion pathway, making of corrosive medium diffusion route become quite twists and turns, is difficult to reach the substrate.
[introduction] glass flake clay
Name: glass flake
Composition: glass flake, curing agent, wear resistant filler, vinyl resin, etc.
characteristic：
Vinyl glass flake clay has excellent chemical resistance, high temperature and wet corrosive gas properties.
Very low water vapor penetration, hardening shrinkage, low linear expansion coefficient.
Fully resist high temperature and rapid temperature changes, wear performance is low.
Room temperature hardening, molding construction is simple, easy to repair.
Scope of application:
The oil storage tank, chemical tanker, railway bridges and other surface coating.
Corrosion protection of steel structures in marine engineering structures.
Corrosion resistant lining of flue gas desulfurization (FGD) device, the maximum operating temperature of the flue gas desulfurization () device is up to 180.
Building surface, drainage ditch, sewage tank corrosion resistant coating.
Using method:
Steel structure surface degreasing cleaning, derusting grade of not less than Sa2.0 or ST3 standard; clean up the surface of concrete, surface moisture <6%, brushing primer 1 to 2, to be dry after construction.
Hand scraper trowel into 1-2mm (each) of the clay layer, a few hours after the design and construction requirements of hardening to the required thickness.
In the corner or the shape of the abrupt change in the appropriate increase in thickness, or with FPR enhanced, and finally with the paint cover 1 to 2 road.
Packaging and preservation:
This product is packaged with 25kg iron, sealed in a cool and dry place to save, 25 degrees under the effective storage period of three months.
會員1.png)